武汉莫诺螺杆泵配件价格合理「多图」冬眠歌词

7分钟前 武汉莫诺螺杆泵配件价格合理「多图」[螺耐斯10e361c]内容：管柱脱落是自由式管柱结构经常发生的一种现象，这是由于正常运转时转子旋转对定子产生的摩擦扭矩方向实际上是定子及油管的连接螺纹的卸扣方向，如果摩擦力矩大于油管扣的上扣扭矩，油管就脱扣。当尾管很重时，还会出现螺纹掳扣。当管柱脱落时，通过作业重新连接好就能恢复生产。如果未发生螺纹掳扣，可以采取对扣方式打捞，如果发生掳扣，必须下打捞工具进行打捞。Column shedding is a common phenomenon of free tube structure, which is due to the direction of rotation of the friction torque generated by the stator rotor during normal operation is actually a stator and tubing connection1 screw shackle direction, if the friction torque is greater than the pipe le on torque, oil pipe tripping. When the tail pipe is very heavy, there will also be a thread caption. When the pipe column falls off, the production can be restored by reconnecting the work. If the le is not threaded, it can be salvaged by the way of the le. If the le occurs, the fishing tool must be salvaged.

管柱脱落的故障现象是：运行电流很低，基本上是电机的空载电流，除了有一股一股的气外，井口基本上无产液，正发循环时油套连通。The failure phenomenon of the string is: the running current is very low, basically the motor's no load current. Besides the gas with a single strand of gas, the wellhead basically has no liquid production, and the oil sleeve is connected when circulating.减少管柱脱落的措施有：将油管上扣扭矩由原来的值提高到值；采用油管螺纹垫片；定子上的装卸短节采用防松螺纹连接；采用油管锚或张力封隔器固定螺杆泵。The measures to reduce the falling off of the pipe string are as follows: increase the torque from the original value to the maximum value; use the oil pipe screw gasket; the loading and unloading joint on the stator is connected by loosening screw thread; and use the oil pipe anchor or tension packer to fix the screw pump.

定转子过早磨损Premature wear of fixed rotor定转子过早磨损主要是由于定转子的间隙过小引起的。The premature wear of the fixed rotor is mainly caused by the small gap between the fixed rotor and the rotor.油管与抽油杆柱磨损Oil pipe and rod string wear油管与抽油杆柱磨损的原因一是因为井斜抽油杆贴在油管壁上引起的，可以通过加抽油杆扶正器使抽油杆柱居中来减轻或消除，另一个原因是定转子不同心及转子的偏心运动造成的，在定子以上加一节内径较大的回转筒即可避免。Tubing and sucker rod wear reason is because the deviation of sucker rod attached to the tubing wall caused by heating, pumping rod centralizer make the rod center to reduce or eliminate, another reason is caused by the eccentric motion of the rotor and the rotor are not concentric, avoid a day the diameter of rotary cylinder in the stator can be larger than.

单螺杆泵工作时，两端分别作用着液体的吸排压力，因此对螺杆要产生轴向推力。螺杆泵厂家建议对于压差小于10千克力/cm2的小型泵，可以采用止推轴承。此外，还通过主动螺杆的中央油孔将高压油引入各螺杆轴套的底部，从而在螺杆下端产生一个与轴向推力方向相反的平衡推力。

单螺杆泵和其它容积泵一样，当泵的排出口完全封闭时，泵内的压力就会上升到使泵损坏或使电动机过载的危险程度。所以，螺杆泵厂家建议使用时在泵的吸排口处，就必须设置安全阀。